The FI-127 Indicator provides a full spectrum of standard features and a flexible options package which make it easily adaptable to almost any force testing application.

• Multiple load cell configuration - It can store configuration data for up to six loadcells or torque measurement devices. The instrument moves rapidly from job to job without recalibration.

• Full range of test values - FI-127 will display a Peak Capture value or Peak Capture plus a First Peak value. The instrument can take a series of readings and display Average Force Over Time, or it can display Over, Under and Accept load values.

• Data capture function - Stores a sequence of loadcell data which the instrument can feed accumulated information to a built-in data base. Data base can store up to 204 consecutive test values for print or later download.

• Easy system interface - It can drive relay coils or send signals to other instruments, computers or PLCs. Its outputs can sound alarms or light warning lights or shut down a system. Its seven inputs can automate data collection from a testing machine or provide an accessory switch to control any of the key pad functions.

Specifications

• Enclosure: NEMA 4X stainless steel enclosure

• Dimensions:
  12" W x 8" H x 4" D (without mounting bracket)
  12.3" W x 11.0" H x 5.3" D (with mounting bracket)

• Power requirements:
  115 Volts AC, +10% to -15% @ 0.3 Amp maximum
  230 Volts AC, +10% to -15% @ 0.15 Amp maximum

• Display: Eight digits, 0.8-inch high, green. seven-segment LED with 8 decimal points

• Annunciators:
  LED: Red
  Display: Force, Peak, First Peak, Tension, Compression
  Units of measure: lbf, kgf, N (programmable to custom units of measure)
  Status: Motion, Center of Zero, Data Send
  Configurable: Under, Accept, Over

• Analog to digital conversion rate: 60 times per second

• Analog input range: ±0.2 to ±5 mV/V/sec

• Internal resolution: 6,291,456 counts/mV/V/sec

• Loadcell excitation: ±5 VDC at 343 mA
  Supports up to twelve 350-ohm loadcells 

• Repeatability: ±0.005% of capacity

• Hysteresis: 0.005% of capacity

• Operating temperature: -40 to +60°C (-40 to +140°F) 

• Humidity: 100% relative humidity including washdown

• Accuracy:
  Span: ±5.0 ppm/°C (-40 to 60°C)
  Zero: ±0.14 mV/°C (-40 to 60°C)
  Linearity: ±0.005% of capacity

• Analog output: 0-5, 0-10 volts
  1-5, 4-20, 10-50 mA

• Battery backed up RAM: Expandable to 128K X 8

• Weight: 12.5 lb, 5.7 kg

• Linearity adjustment: The instrument may be calibrated for up to six different load cells. Each load cell may be calibrated at two to ten points, providing best fit linearization. 35 total calibration points available. 

• Cutoff Outputs: Three (3) standard outputs used to drive relay coils or logic inputs
  Open drain MOSFET
  Flyback diode protection
  Max voltage: 60 VDC
  Max current: 200 mA
  24 VDC source with 150 mA max output current

• Remote inputs: Seven standard inputs
  Inputs 6 and 7 set and reset an internal bit labeled "8"
  Logic level input with pull-up resistor is activated by switch to ground 

• Serial output:
  Hardware configurable for RS-232, RS-485/RS-422 or current loop.
  Baud rate adjusted in software from 300 to 19.2K bits per second.
  Parity, number of data bits and number of stop bits front-panel configurable. 

• Accessory power: +5VDC with 200 mA max output current to operate external scanners, etc. 

• Standard outputs:
  Three cutoff outputs, open collector design
  Relay power supply, 24V at 150 mA
  5 volts at 200 mA for scanner power source
  Bi-directional serial port (RS-232 or RS-422/485 or 20 mA current loop) Includes round 4-pin watertight connector for quick access to serial port. 

• Agencies: NEMA 4X, CUL, FCC Class A

• Operational keys:
  Five yellow standard keys: Zero, Peak Reset, Data Send, Units, Select
  Three programmable function keys: F1, F2, F3
  Numeric keys: 0-9, ±sign, decimal (.) Enter, < -, and Escape

• Display update rate: Selectable (1, 2, 5, 10 times/second)

• Capacity selections: 999,999 with decimal located from zero to five places

• Incremental selections: Multiples and sub-multiples of 1, 2, 5

• Programmable selections: Zero range, peak, first peak, data capture, motion detection, 10-point linearization. 

• Time and date: Battery protected real time clock 

• Internal resolution: 6,291,456 counts per mV/V per second

• Harmonizer^TM digital filtering: Fully programmable to ignore noise and vibration 

• Self diagnostics: Display, keys, I/O ports, voltages

• Options:
  Additional serial cards
  BCD parallel card
  16 output & 8 input card
  Analog output

Back to Main Dillon Quantrol Page

Click here for Brochure
(Adobe PDF)

Top